Introduction

Cat C7 Iap Valve Location Map
Cat C7 Ipr Valve Location
Cat C7 Iap Valve Location Chart
Cat C7 Icp Sensor Location

C7 Engines Illustration 2 g01114317 Typical view of the left side of the C7 engine (1) Fuel pressure sensor (if equipped) (2) J500/P500 Injection actuation pressure control valve connector (3) Injection actuation pressure sensor (4) Engine coolant temperature sensor (5) J300/P300 Injector valve cover entry connector.
How To Troubleshoot HEUI Systems and IAP faults. 3126, C7, and C9 Cat Engines. C7 Engines Illustration 2 g01114317 Typical view of the left side of the C7 engine (1) Fuel pressure sensor (if equipped) (2) J500/P500 Injection actuation pressure control valve connector (3) Injection.
CATERPILLAR C7/C9 ENGINES The Bendix ® BA-921 compressor in the C7/C9 air induction system (see Figure 10) receives its air from the engine's intake manifold (turbocharged). During the pumping condition (loaded mode), the air ﬂ ows from the engine intake manifold through the inlet check valve and inlet line to the compressor inlet port.

Cat cat ® c7 acert™ industrial diesel engine caterpillar c7 acert™. Cat c7 engine oil diagram schematic diagram data cat c7 acert wiring diagram diagram data schema cat c7 engine oil diagram. Cat C7 Iap Valve Location Patti Labelle The Winner Rar Seiler.

Illustration 1 g01447542
Fuel System Diagram

(1) Unit injector hydraulic pump

(2) Oil flow to engine

(3) Oil filter

(4) Engine oil pump

(5) Injectors

(6) Connector for the IAP control valve

(7) Oil cooler

(8) High pressure oil passage

(9) IAP sensor

(10) Fuel supply passage

(11) Fuel transfer pump

(12) Secondary fuel filter

(13) Primary fuel filter/water separator

(14) Fuel tank

(15) Fuel pressure regulator

(16) Back of camshaft gear

Cat C7 Iap Valve Location Map

(17) Speed/timing sensors

(18) ECM

Cat C7 Ipr Valve Location

(19) Boost pressure sensor

(20) Engine coolant temperature sensor

(21) Engine oil pressure sensor

(22) Inlet air temperature sensor

(23) Engine oil level switch

(24) Atmospheric air pressure sensor

(25) Wastegate control valve

The operation of the Hydraulic Electronic Unit Injector (HEUI) fuel system is completely different from any other type of fuel system that is actuated mechanically. The HEUI fuel system is completely free of adjustment. Adjustments to the components that are mechanical can not be made. Changes in performance are made by installing different software in Electronic Control Module (ECM) (18) .

This fuel system consists of six basic components:

Hydraulic Electronic Unit Injector (HEUI) (5)
Electronic Control Module (ECM) (18)
Unit injector hydraulic pump (1)
Fuel transfer pump (11)
Injection Actuation Pressure sensor (9)

Note: The components of the HEUI fuel system are not serviceable. These fuel system components must not be disassembled. Disassembly will damage the components. If the components have been disassembled, Caterpillar may not allow a warranty claim or Caterpillar may reduce the warranty claim.

Component Description

Hydraulic Electronic Unit Injector

The HEUI fuel system utilizes a hydraulically actuated electronically controlled unit injector (5) .

All fuel systems for diesel engines use a plunger and barrel in order to pump fuel under high pressure into the combustion chamber. This fuel is pumped into the combustion chamber in precise amounts in order to control engine performance. The HEUI uses engine oil under high pressure in order to power the plunger. All other fuel systems use a fuel injection pump camshaft lobe in order to power the plunger. Because the HEUI is much different, a technician must use different troubleshooting methods.

The HEUI uses engine lubrication oil that is pressurized from 6 MPa (870 psi) to 28 MPa (4050 psi) in order to pump fuel from the injector. The HEUI operates in the same way as a hydraulic cylinder in order to multiply the force of the high pressure oil. By multiplying the force of the high pressure oil, the HEUI can produce injection pressures that are very high. This multiplication of pressure is achieved by applying the force of the high pressure oil to a piston. The piston is larger than the plunger by approximately six times. The piston that is powered by engine lubrication oil under high pressure pushes on the plunger. This engine lubrication oil under high pressure is called the actuation pressure of the oil. The actuation pressure of the oil generates the injection pressure that is delivered by the unit injector. Injection pressure is greater than actuation pressure of the oil by approximately six times.

Low actuation pressure of the oil results in low injection pressure of the fuel. During conditions of low speed such as idle and start, low injection pressure is utilized.

High actuation pressure of the oil results in high injection pressure of the fuel. During conditions of high speed such as high idle and acceleration, high injection pressure is utilized.

There are many other operating conditions when the injection pressure is between the minimum and the maximum. Regardless of the speed of the engine, the HEUI fuel system provides infinite control of injection pressure.

Cat C7 Iap Valve Location Chart

Electronic Control Module (ECM)

Electronic Control Module (ECM) (18) is located on the left side of the engine. The ECM is a powerful computer that provides total electronic control of engine performance. The ECM uses data from engine performance that is gathered by several sensors. Then, the ECM uses this data in order to make adjustments to the fuel delivery, injection pressure and injection timing. The ECM contains programmed performance maps (software) in order to define horsepower, torque curves and rpm. This software is commonly called the personality module.

The engine does not have a replaceable personality module. The personality module is a permanent part of the ECM. The personality module for the engine can be reprogrammed by Caterpillar Electronic Technician (Cat ET).

ECM (18) logs faults of engine performance. Also, the ECM is capable of running several diagnostic tests automatically when the ECM is used with an electronic service tool such as the Cat ET or the Electronic Control Analyzer Programmer (ECAP).

Unit Injector Hydraulic Pump

Cat C7 Icp Sensor Location

Illustration 2 g01447556
(1) Unit injector hydraulic pump

Unit injector hydraulic pump (1) (high pressure oil pump) is located at the left front corner of the engine. The unit injector hydraulic pump is a variable delivery piston pump. The unit injector hydraulic pump uses a portion of the engine lubrication oil. The unit injector hydraulic pump pressurizes the engine lubrication oil to the injection actuation pressure that is required in order to power the HEUI injectors.